Radio quiet site in Scotland required for 50 MHz meteor scatter reception

The GB3MBA beacon near Mansfield in England operates on 50.408 MHz and was set up to investigate reflections from meteor trails.

As the map shows above, the project team has already has a number of dedicated receivers set up to monitor the 6m band for any meteor reflections from the beacon. They are however looking to for a quiet radio site in Scotland for a receiver there.

Brian, G4NNS writes... "What is needed is a reasonably radio quiet site with no nearby 6 m transmissions, with power, (10 W or less) and an internet connection. The data stream is about the same as an audio stream so not excessive. Ideally the site would be a minimum of 200km North of the beacon which is located near Mansfield 53.10N, 1.22W.

An astronomy society with  a dark sky observing site would be ideal. We would need someone local who is radio "savvy" to check the site and help with installation.  A locally sourced mast of 3 or 4m would be handy but we can supply all other materials.  We are trying to achieve a range  of different reflection geometries for each meteor event. When we can make observations from a sufficient number of  different directions it may be possible, by using Doppler measurements, to calculate the trajectory and hence radiant of the meteor."

More information about the beacon can be found here... https://ukmeteorbeacon.org

Reception of the 50 MHz GB3MBA beacon during the Quadrantids meteor shower - 4th Jan 2024

Back in December, I carried out an experiment to find and record the peak of the Geminids meteor shower by listening to the GB3MBA 50 MHz beacon which is 500kms from my location. See post HERE

On the afternoon of 4th of January 2024, there was the peak of the Quadrantids meteor shower which tends to be very narrow but intense. This time, I just took some screenshots of the meteor reflections.

Introduction... Back in 2022, a new radio beacon called GB3MBA was put on air on the 50 MHz band and its primary purpose was carrying out meteor scatter experiments. Located near the town of Mansfield in the centre of England, the beacon runs 75-watts into a small Moxon antenna which beams straight up.

Unlike most amateur radio beacons, this one is basically a carrier that is on nearly all of the time which is exactly what is needed for meteor scatter experiments. The main coverage area is the UK itself but as I'm 502 kms from the beacon, I'm close enough for it to be of use.

For the Quadrantids meteor shower, I was using a Yaesu FT817 on USB as a receiver and the antenna was a 2-element Yagi in the attic of my house. The antenna was beaming about 120 degrees which is about 45 degrees off the beam heading for the beacon (The choice of beam heading is determined by the space in the attic and I wasn't trying to beam away from the beacon).

Quadrantids screen shots...

The image above shows the composite collection of seven different screenshots. As can be seen, there was plenty of evidence of pings and bursts from the GB3MBA beacon.

The images on the blog are quite small and a link to a larger version of the image is on Facebook HERE.

I'll use the more detailed example above to explain what you are looking at. The time is moving from right to left and you will notice the 30-second timestamps. As my receiver isn't GPS locked, I'm probably around 5 Hz off frequency which is ok. 

If I was hearing the beacon directly, it would show up as a solid yellow line going across the centre of the screen. Instead, you are looking at the signal reflecting / refracting off the trail of electrons left behind by the meteor as it burnt up. As these electrons are in motion in different layers of the upper atmosphere, there is some doppler shift on the signal.

In the example above, the 50 MHz signal lasted for about 90-seconds.

The signal on the far right of the image above is one of my favourites. This is called an 'epsilon' echo as it twirls around. What causes such a complex pattern as opposed to the other 'smudges'?

Link...
1) GB3MBA website

Meteor scatter experiment with the 2023 Geminid shower

In this post, I'll outline how I used an amateur radio beacon 500kms away to find the peak of the 2023 Geminids meteor shower and what else I noticed.

Introduction... Back in 2022, a new radio beacon called GB3MBA was put on air on the 50 MHz band and its primary purpose was carrying out meteor scatter experiments. Located near the town of Mansfield in the centre of England, the beacon runs 75-watts into a small Moxon antenna which beams straight up.

Unlike most amateur radio beacons, this one is basically a carrier that is on nearly all of the time which is exactly what is needed for meteor scatter experiments. The main coverage area is the UK itself but as I'm 502 kms from the beacon, I'm close enough for it to be of use.

I expected that most of the signals that I would hear would be from meteors burning up over Wales and would be arriving at my location about 20 degrees above the horizon.

Experiment Objectives... This is what I wanted to do...

• Carry out an experiment as a 'proof of concept', take measurements, gain experience and see how I could improve on it.
• Take 'hard measurements' with real data as opposed to just forming an opinion.
• See if I could plot and find the peak of the 2023 Geminid meteor shower as a form of 'citizen science'.

Methodology & Equipment... For the previous few days before the peak, I was listening to meteor bursts from the beacon to establish the best method to carry out the experiment.

Radio... I was using an old Kenwood TS-690 amateur radio transceiver which still works fine and is pretty sensitive. I tuned it to 50.408 MHz and set the mode to CW. It drifts a few Hz with the changes of temperature in the shack but it was fine for this experiment. I just needed to be careful to make sure I was always on frequency.

Antenna... In the run up to the experiment, I used a 2-element Yagi in my attic beaming 120-degrees (east-south-east) to get ready. This was beaming about 45 degrees away from the beacon and being indoors, it wasn't optimum. Just before the experiment, I built a vertical T2LT (flowerpot) half-wave antenna and mounted it about 6-metres above the ground. It had a clear view of the sky towards Wales and the beacon.

Software... I used the SpectrumLab programme to look at the audio spectrum so that I could see any bursts and pings of signal. Under the 'Quick Settings', I used Slow Morse Reception ("QRSS") and I then selected 'Slow CW, 30 sec/dot'. 

I knew it wasn't practical to look at a screen for hours on end. At this setting, the audio spectrum is about 30 Hz wide and it takes about 1h 20m for the signals to drift from right to left across the screen. What this meant in reality was that I could look at the screen every 60-80 mins, count the signals on the screen and record the number of pings and bursts.

What to record?... I knew whatever I did, it had to be consistent for the observing period. I decided to use the number of signals seen in a 30-minute period. If it was a long burst or a short ping, I counted it as one signal. 

This raises the obvious question... should I count the number of pings and bursts, should I record the strong signals versus the number of weak signals? The problem is where do I draw the line? I knew I'd see long bursts, short pings and everything in between. It was the same for the signal strength... what's a 'strong signal'? 

I decided I just wanted 'hard data'. Was there a meteor scatter signal present on the screen... Yes or No. It's simple and there's no ambiguity.

Time period... For the experiment, I counted the number of meteor scatter signals from 17:30 UTC on the 14th of December to 22:00 UTC on the 15th of December 2023...a period of 28 hours and 30 minutes. This time frame coincided with the predicted peak of the Geminid meteor shower.

Results... This is the chart that I generated for the 28.5 hour period.

The recording period starts at 17:30 UTC on the 14th of December when the Geminid constellation and radiant point would be just above the horizon. I'll break down the chart in more detail below but the key thing to note is the peak at about 20:00 UTC on the 14th of December.

I had intended to stop recording early in the morning of the 15th but I was wondering if the peak was really the peak? Would there be another peak 24-hours later when the radiant point would be at the some position in the sky? As you can see, there was no peak 24-hours later. I had actually recorded the peak of the Geminids on the 14th.

Results - Time Frame - 17:30 UTC 14th Dec to 05:30 UTC on the 15th of December... The peak, the dip and the highest radiant...

The first 12-hours is shown above in more detail.

The start... I did a search on Google and it said that the constellation Gemini would rise above the horizon in London at 17:23 UTC. I'm 8.5 degrees west which means it would be 33 mins later... 17:56 UTC. The mid point might be say 17:39 UTC? I found another website which said that the radiant point would rise around 16:07 UTC??

This is further complicated by the fact that we're really looking at a time when meteors from radiant point in the Geminids would be hitting the atmosphere 100kms about Wales? I think 17:30 was a good enough time to start.

The peak... Between 19:00 and 20:30 UTC, I had counts of 15, 19 & 21 for each of the 30-minute intervals.

This is a screenshot I took during this period.

First, I'll explain what you are looking at. The vertical axis is a 30 Hz wide segment of the audio spectrum. The screen is moving from right to left and the white dotted lines are the 5-minute time intervals.

If I was hearing the beacon signal directly, it would be a solid yellow line running from right to left across the centre of the screen.

What you are looking at are the pings and bursts of meteor scatter signals which are spread out across the audio spectrum due to doppler shift.

Prior to the shower, I had seen that the peak was expected at 19:30 UTC on the 14th of Dec. Looking at my screenshot, I think the peak of the 2023 meteor shower occurred between 19:55 and 20:20 UTC on the 14th of December.

The dip??... I did make a note of how weak the reflections were from 22:30 and 00:00 UTC and this can be clearly seen in the chart above. 

As the meteor shower radiant moves slowly across the sky, the angles between the transmitter, receiver and the trails of the meteors will change. At some points, the meteor trails will be parallel between my location and the beacon and at other points, the trails will be perpendicular.

I suspect the dip is due to the geometry of the meteor trails but I'm not sure. It could also be just a statistical error. I would need to repeat the observations on several days around this time period to see if it repeats.

Maximum elevation... At about 01:30 UTC, the radiant point was supposed to be at its highest elevation which was about 71 degrees above the horizon.

Before the experiment, I was wondering if this mattered? Would there be some sort of peak when the radiant peak was at its highest point in the sky? The answer seems to be no, there is no peak.

Results - Time Frame - 01:30 UTC to 11:00 UTC on the 15th of December... The daily morning peak...

When it comes to random meteors entering the atmosphere, the best time for signals tends be around 6am local time. This is because the speed of the earths rotation is added to the speed of the meteors resulting in more energy to dissipate.

This enhancement can be clearly seen in the chart above. It increases after 02:00 UTC and decreases after 10:00 UTC. For me at least, it seemed to be an eight hour window.

The converse is also true. At 6pm local time, the speed of the earth's rotation is subtracted from the original speed of the meteors.

This means that the peak of the 2023 Geminids at about 20:00 UTC happened just two hours after 6pm for me which isn't a great time.

As I was looking at the original chart with the 28.5 hour display, I realised that I was looking at two peaks but both were completely different. One is a fixed peak and the other is a variable peak.

The fixed peak was the peak of the Geminids at about 20:00 UTC on the 14th of December. That's fixed, the peak is the peak.

The morning peak however will depend on where you are. Somewhere in the world, the peak of the Geminids meteor shower will coincide with 6am local time. That turns out to the western half of the Pacific. Anyone in say Hawaii, Alaska, Korea, Japan, east China and the Philippines should have seen some very good meteor bursts and pings. That is of course conditional on having the radiant point above the horizon and that will depend on the location.

Results - Time Frame - 09:00 to 22:00 UTC on the 15th of December... This is the last 13 hours of the plot in more detail...

The radiant point for the Geminids sets about 10:00 UTC and a drop in numbers can be seen. The signals from about 10:00 to 17:30 UTC are random meteors and are not Geminids as the radiant point is below the horizon.

You can see it was particularly poor from 16:30 to 17:30 UTC. Then the Geminids radiant point comes above the horizon and the numbers increase again.

Other observations... Aircraft Scatter... I've seen plenty of aircraft scatter on signals before but I was really surprised to see it on a signal from 500kms away.

These can be very easy to miss. On the QRSS 3 setting, these appear as almost horizontal lines due to the larger vertical scale and faster scrolling speed. On QRSS 30 as used above, the slant becomes a lot more obvious.

As you can see, the doppler shift is in the region of 5-7 Hz. When I was seeing these signals appear, I would check FlightRadar 24 and sure enough, there was often a large plane to the west of Aberstwyth on the west coast of Wales. This is around the halfway point from the beacon to my location.

This suggests to me that while the GB3MBA beacon is 'beaming straight up', there is plenty of RF heading towards the horizon as well.

You'll notice as well that the trails last for about 90 seconds which should be enough for digital modes like MSK144 or possibly FT4? I'd have no doubt that a lot of those one off FT8 decodes on the 10m and VHF bands that people get are due to aircraft scatter like this.

Additional Notes...

• I couldn't tell if any meteor heard was a Geminid or not for the time the radiant was above the horizon.
• Despite all of the 'streaks' visible on the screen, the signals were actually pretty weak. Many were not audible to my ear and I'd say the strongest signals were probably something like 519. 
• The process that I used was very labour and time intensive. I literally had to set an alarm to wake up every 60-80 mins overnight and take the measurements.
• My resolution was 30 mins which may have limited the resolution in that I couldn't tell if two very close bursts were one or two.

In Conclusion... I think the experiment overall was a success. I was able to see the peak of the 2023 Geminid meteor shower which was from 19:55 to 20:20 UTC on the 14th of December.

I'm sure there is room for improvement but I think this is a useful 'citizen science' project which can be done by anyone with a good receiver and antenna. This method is also easy enough that it's not restricted to those from a radio background. 

Anyone with a serious interest in astronomy and meteor research could do this and consider it as an additional tool. This system works regardless of the weather. While 'visual' amateur astronomers need clear skies, the 'radio' based amateur astronomer can carry on regardless.

It might make an excellent project for an astronomy or radio club and maybe give a presentation to students as part of a STEM outreach programme

I think it proves that GB3MBA is indeed a very useful beacon for meteor scatter research and I think the challenge now is for them to make more people aware of it.

You can tell from the length of this post that this was a deep dive down the rabbit hole for me. As soon as I had one question answered, I thought up of two more additional questions.

The future??.. I'd see these as areas for improvement.

1. My antenna was a vertical half-wave which is omni-directional. I think something like a 3-element Yagi would give me at least 6dB more gain, reduce noise and result in more pings and bursts.
2. My experiment was for 28.5 hours with a resolution of 30 mins. I think in the future, I would use QRSS 3 with a finer resolution of 10 minutes and plot the period around the predicted peak in more detail.

More information...

For more information on the GB3MBA beacon, go to https://ukmeteorbeacon.org/

There is also the BRAMS beacon in Belgium on 49.970 MHz which might be of interest... https://brams.aeronomie.be/